You are not logged in.
Hi, please help me to solve this problem.
I have:
-Raspberry Pi 3
-A4988
-Led
-Nema 17
-5 inch screen
-endstop
Wired them all according schematic from this site.
1. When i test Projector calibration, screen and shutter works. The test images appear on the screen, shutter (LED) also works
2. Step motor is also working
3. End stop is also working
4. When i send STL file to print:
4.1. First layer appears on the screen. LED goes on.
4.2. Then on the secon layer "RAMPS Sync - Waiting for done message from RAMPS" and it is waiting command from RAMPS.
But there is no RAMPS, i am doing direct control.
What is the problem here ?
Thanks.
Here is the log
Info 1 2017-11-21 13:50:32.919633 RAMPS Sync Waiting for done message from RAMPS
Debug 1 2017-11-21 13:50:29.912107 Shutter Shutter Close
Debug 1 2017-11-21 13:50:29.91174 Image Clear screen
Debug 1 2017-11-21 13:49:39.860525 Printing Curing for 49.999998976 seconds
Warning 1 2017-11-21 13:49:39.656643 Image Display layer public/plates/1/1.png
Debug 1 2017-11-21 13:49:27.65625 Shutter Shutter Open
Notice 1 2017-11-21 13:49:27.655941 Gcode Position set to 0.04
Info 1 2017-11-21 13:49:27.655736 RAMPS Sync Ready for the next RAMPS movement
Info 1 2017-11-21 13:49:27.655672 RAMPS Sync Waiting for done message from RAMPS
Debug 1 2017-11-21 13:49:27.654915 Pulsing Movement Finished Pulse 2667 / 2667 ; Height 312 / 2979 ; Time 21.789695529
Debug 1 2017-11-21 13:49:05.864994 Pulsing Moving Down 2667 pulses 5.000625 mm
Debug 1 2017-11-21 13:49:05.864829 Pulsing Movement Finished Pulse 312 / 312 ; Height 0 / 312 ; Time 0.571915698
Debug 1 2017-11-21 13:49:05.292628 Pulsing Moving Down 312 pulses 0.585 mm
Debug 1 2017-11-21 13:49:05.292435 Pulsing Moving to Layer
Debug 1 2017-11-21 13:49:05.292301 Shutter Shutter Close
Debug 1 2017-11-21 13:49:05.292231 Image Clear screen
Error 1 2017-11-21 13:49:05.292149 Gcode External Call Problem exit status 1 TOKEN is unset or empty: Did you create /etc/pushover.conf or specify -T on the command line?
Debug 1 2017-11-21 13:48:36.658411 Pulsing Movement Finished Pulse 6137 / 100000000 ; Height -2646 / 0 ; Time 5.928158951
Warning 1 2017-11-21 13:48:36.658332 Pulsing Limit touched position reset
Notice 1 2017-11-21 13:48:36.658236 GPIO Limit has been touched
Debug 1 2017-11-21 13:48:34.896196 WiFi Connected to NETIS
Offline
Remove any [[WaitForDoneMessage]] keyword from gcode boxes on both profile and setup pages.
Offline
Thanks Shahin !
I removed "Waiting for done message from RAMPS" from default resin profile and it worked.
Offline
hi shahin
How to sync nanoDLP and Grbl together. [Waitfordone] not work and [delay s"] is not useful for different speeds.
thanks alot
Offline
Use latest version of marlin as it already supports nanodlp WaitForDone on the official release.
Offline