Stop print error - Direct control

Thiengod · 2017-11-19 16:52:55

I use direct control, but when I stop printing, it fails with error "Waiting for done message from RAMPS" and I can not do anything except turn off the RPi3 power.

nanodlp.debug.-1680081502.zip

Shahin · 2017-11-19 17:35:26

Remove [[WaitForDoneMessage]] from gcode boxes.

Thiengod · 2017-11-20 02:23:15

Hi Shahin
I don't use [[WaitForDoneMessage]] for any gcode boxes.

Shahin · 2017-11-20 07:39:54

I have checkout log files look like you are receiving "Done message from RAMPS has been received" not "Waiting for done message from RAMPS" right? If so, there should not be any movement issue.

Thiengod · 2017-11-20 12:57:12

Sorry for the confusion. I received the message "Done message from RAMPS has been received". it doesn't have any movement. I can not do anything after that, even shutdown and reboot. Nanodlp crashes I have to turn off the power

Shahin · 2017-11-21 05:12:10

Could you explain where movement works and where it does not? For example if manual movement works and etc.

Thiengod · 2017-11-21 05:22:45

Hi Shahin,
This error sometimes appears, there is no command that can execute. The printer must turn off the power

Shahin · 2017-11-21 05:42:16

With all versions or appeared with recent versions?

Thiengod · 2017-11-21 06:48:35

I don't know. I switched to using direct control about 1 month ago. I installed new Pi3 and nanoDLP to be sure no problems with the old settings but still error

Shahin · 2017-11-23 07:04:04

I have tried it locally on my pi. I could not reproduce it. Do you have any RAMPS wired to nanodlp?

Thiengod · 2017-11-23 08:43:48

I don't connect RAMPS to nanodlp. Shield Connection is disabled

Last edited by Thiengod (2017-11-23 09:01:14)

Thiengod · 2018-03-15 03:00:09

Hi Shahin
The error occurs when the stop is pressed while the Z-axis moving down to the print position after pressed "Print From Start"

Shahin · 2018-03-15 05:53:38

It is not important you have shield enabled or not, you still could use keywords such as [[WaitForDoneMessage]] which freeze printer until receive Z_move_done message.

nanoDLP

#1 2017-11-19 16:52:55

Stop print error - Direct control

#2 2017-11-19 17:35:26

Re: Stop print error - Direct control

#3 2017-11-20 02:23:15

Re: Stop print error - Direct control

#4 2017-11-20 07:39:54

Re: Stop print error - Direct control

#5 2017-11-20 12:57:12

Re: Stop print error - Direct control

#6 2017-11-21 05:12:10

Re: Stop print error - Direct control

#7 2017-11-21 05:22:45

Re: Stop print error - Direct control

#8 2017-11-21 05:42:16

Re: Stop print error - Direct control

#9 2017-11-21 06:48:35

Re: Stop print error - Direct control

#10 2017-11-23 07:04:04

Re: Stop print error - Direct control

#11 2017-11-23 08:43:48

Re: Stop print error - Direct control

#12 2018-03-15 03:00:09

Re: Stop print error - Direct control

#13 2018-03-15 05:53:38

Re: Stop print error - Direct control

Board footer