nanoDLP

joaoreina

Member

From: Paris, France

Registered: 2016-02-19

Posts: 20

Build 1149 doesn't change distribution

Good morning,

I've recently uploaded nanoDLP to my microSD card, build 1149, I would like to change the distribution to muve3D, but it apparently doesn't happen
I ended up inserting some of the necessary gcode and it is working fine, but just don't know if I'm missing something from that distribution

thanks

Shahin

Administrator

Registered: 2016-02-17

Posts: 3,541

Re: Build 1149 doesn't change distribution

ssh into rpi
type following commands and reply back the reponses

ls -l /home/pi/printer/db/
ls -l /home/pi/printer/distro/muve3d/opt/db/

Keep dashboard open on a tab, change distribution, checkout dashboard error reports, do you see anything important?

joaoreina

Member

From: Paris, France

Registered: 2016-02-19

Posts: 20

Re: Build 1149 doesn't change distribution

pi@raspberrypi:~ $ ls -l /home/pi/printer/db/
total 20
-rw-r--r-- 1 root root 1637 Apr 29 13:57 buttons.json
-rw-r--r-- 1 root root  284 Apr 29 13:14 calibration.json
-rw-r--r-- 1 root root 1739 May  3 13:44 machine.json
-rw-r--r-- 1 root root 1435 May  3 13:50 plates.json
-rw-r--r-- 1 root root 3519 May  3 14:02 profiles.json
pi@raspberrypi:~ $ ls -l /home/pi/printer/distro/muve3d/opt/db/
total 16
-rw-r--r-- 1 pi pi 1984 Apr 25 15:21 buttons.json
-rw-r--r-- 1 pi pi  307 Apr 25 15:21 calibration.json
-rw-r--r-- 1 pi pi 1901 Apr 25 15:21 machine.json
-rw-r--r-- 1 pi pi 2779 Apr 25 15:21 profiles.json

> Keep dashboard open on a tab, change distribution, checkout dashboard error reports, do you see anything important?
you mean, check the Application log on the nanoDLP dashboard, while changing distribution?

Shahin

Administrator

Registered: 2016-02-17

Posts: 3,541

Re: Build 1149 doesn't change distribution

Files looks fine.

Yes, exactly.

joaoreina

Member

From: Paris, France

Registered: 2016-02-19

Posts: 20

Re: Build 1149 doesn't change distribution

there was no event reported on the dashboard application log
something I didn't mentioned earlier, I also tried to use the update instructions on the muve documentation, through ssh, but ended up in the same 1149 version.
How do I know in which distribution am I? I can only tell by the uploaded printer profiles and some Gcode in the hardware setup

Shahin

Administrator

Registered: 2016-02-17

Posts: 3,541

Re: Build 1149 doesn't change distribution

Run command below to manually change distribution.
Lets see if we could get any error reported.

sudo /home/pi/printer/change-distro.sh muve3d

File below contains your current distribution details

/home/pi/printer/build

joaoreina

Member

From: Paris, France

Registered: 2016-02-19

Posts: 20

Re: Build 1149 doesn't change distribution

Hi,
my build file does say "muve3dls", so I suppose the change worked
but as I said earlier, usually this change would upload some specific "printer profiles" and the inclusion of some custom Gcode to work with the mUVe printer.
thanks

Shahin

Administrator

Registered: 2016-02-17

Posts: 3,541

Re: Build 1149 doesn't change distribution

Not much difference among distribution other than settings and the mask file.