You are not logged in.

#1 2017-06-05 17:39:37

Shahin
Administrator
Registered: 2016-02-17
Posts: 3,429

SLS 3D Printers

We have plan to add SLS support to NanoDLP.

Is there anybody working on low cost SLS printer and want to collaborate with us?

Offline

#2 2017-06-23 17:54:31

NeelD
Member
Registered: 2017-06-02
Posts: 44

Re: SLS 3D Printers

Wanhao said they are working on it.

Offline

#3 2019-09-19 14:01:41

alkg
Member
Registered: 2019-04-10
Posts: 11

Re: SLS 3D Printers

Is it possible to control the laser using nanodlp? as in the photo

Screenshot-2.jpg


What does the laser mean in the photo, what is this function?Which laser is needed?

Screenshot-3.jpg

Last edited by alkg (2019-09-19 14:04:05)

Offline

#4 2019-09-21 15:08:24

Shahin
Administrator
Registered: 2016-02-17
Posts: 3,429

Re: SLS 3D Printers

Provide link to documentation of the pictured device. No idea what is this.

Offline

#5 2019-09-21 18:01:36

alkg
Member
Registered: 2019-04-10
Posts: 11

Re: SLS 3D Printers

This is controlled via the LPT port, using the G code  . Apply for laser show

https://ru.aliexpress.com/item/32863575 … CmM5NDLNog

There is a ready-made solution but I don’t know if it works

https://ru.aliexpress.com/item/32973601 … 2e0e1xfxvj

Last edited by alkg (2019-09-21 18:02:48)

Offline

#6 2019-09-23 03:13:39

Shahin
Administrator
Registered: 2016-02-17
Posts: 3,429

Re: SLS 3D Printers

LPT is not supported maybe if it setupped in a way to behave exactly like Serial it would work on nanodlp.

Offline

#7 2019-09-24 10:09:03

elshad66
Member
Registered: 2017-03-31
Posts: 118

Re: SLS 3D Printers

forget ,,,,, build a printer on galvo, it's hemorrhoids
killed a lot of time and energy

забей,,,,, строить принтер   на гальво ,  это  геморрой 
уйма  сил и времени угрохал

https://www.youtube.com/watch?v=02jm43UE-vk

Last edited by elshad66 (2019-09-24 10:14:51)

Offline

#8 2019-11-11 23:25:48

mgillan
Member
Registered: 2019-09-11
Posts: 8

Re: SLS 3D Printers

Hi Shahin, is there existing support for SLA (laser-based)? I have just discovered that there is now a laser option as shown in alkg's photo above, not sure when that was added. If so, what kind of galvos can you control? Is there another thread that addresses this?

Offline

#9 2019-11-12 05:53:54

Shahin
Administrator
Registered: 2016-02-17
Posts: 3,429

Re: SLS 3D Printers

You need RAMPS. New option (8 months old) just generate per layer gcode to move galvo around in x,y axis to fill parts.

Offline

#10 2019-11-12 08:01:08

alkg
Member
Registered: 2019-04-10
Posts: 11

Re: SLS 3D Printers

Shahin wrote:

You need RAMPS. New option (8 months old) just generate per layer gcode to move galvo around in x,y axis to fill parts.

RAMPS 1.6 Plus   ?

Offline

Board footer

Powered by FluxBB