You are not logged in.
Pages: 1
z axis won't move after update
Offline
Do you use RAMPS or Direct control?
Could you paste activity log on dashboard?
I have recently updated z-axis movement module.
Offline
Direct control with Rasp + applied motion driver
printer.mem
2017-06-03 07:39:15.808 {"Layer":"2","module":"Hardware","level":"Notice","msg":"Initializing build # 1465 - generic"}
2017-06-03 07:39:15.857748 {"Layer":"2","module":"Hardware","level":"Debug","msg":"Stepper motor enabled"}
2017-06-03 07:39:15.858013 {"Layer":"2","module":"Shutter","level":"Debug","msg":"Shutter Close"}
2017-06-03 07:39:15.858048 {"Layer":"2","module":"Pulsing","level":"Debug","msg":"Moving to top"}
2017-06-03 07:39:15.858199 {"Layer":"2","module":"Terminal","level":"Notice","msg":"Terminal Reader Activated"}
2017-06-03 07:39:15.858307 {"Layer":"2","module":"Pulsing","level":"Debug","msg":"Moving Up 100000000 pulses 100000 mm"}
2017-06-03 07:39:15.858453 {"Layer":"2","module":"GPIO","level":"Notice","msg":"Limit has been touched"}
2017-06-03 07:39:15.858615 {"Layer":"2","module":"Pulsing","level":"Warning","msg":"Limit touched position reset"}
2017-06-03 07:39:15.858768 {"Layer":"2","module":"Pulsing","level":"Debug","msg":"Movement Finished Pulse 0 / 100000000 ; Height 6000 / 0 ; Time 0.000310098"}
2017-06-03 07:39:15.858848 {"Layer":"2","module":"Pulsing","level":"Debug","msg":"Moving to Stop Position"}
2017-06-03 07:39:15.858932 {"Layer":"2","module":"Pulsing","level":"Debug","msg":"Moving Down 6000 pulses 6 mm"}
2017-06-03 07:39:16.010105 {"Layer":"2","module":"WIFI","level":"Warning","msg":"WIFI interface wlan0 detected"}
2017-06-03 07:39:16.022457 {"Layer":"2","module":"WiFi","level":"Debug","msg":"Status Monitoring"}
2017-06-03 07:39:16.078338 {"Layer":"2","module":"WIFI","level":"Warning","msg":"Connecting to FFff0987"}
2017-06-03 07:39:19.030341 {"Layer":"2","module":"Pulsing","level":"Debug","msg":"Movement Finished Pulse 6000 / 6000 ; Height 0 / 6000 ; Time 3.171171042"}
2017-06-03 07:39:26.023126 {"Layer":"2","module":"WiFi","level":"Debug","msg":"Connected to FFff0987"}
Last edited by 1125lbs (2017-06-03 07:45:03)
Offline
Do it come down 6mm after power up?
There is no manual movement up or down?
Offline
there's no movement, reboot the babe, the log says its done with routine put physicaly nothing changes,
I just come to lab ( did not turned the machine down) and see on trello board that you havve update pre -calculated pulse length so i just update it,
then the "buildhead" stay parked on 6mm waiting position, after update its showing on calib. page that its currently on 0000000 position but its not, so no movement was done after upgrade
Offline
I have found an issue. Please, upgrade and let me know if it fix the issue.
Offline
I have found an issue. Please, upgrade and let me know if it fix the issue.
Issue Fixed !
thank you very much!
Offline
Could you share your impression of rewritten movement module? Specially in terms of speed and movement irregularity.
Offline
Hello fellows,
For shure,
Currently my setup is running with direct drive ( Applied Motion STR8 driver ), on early versions i had experiencing some cogging effect, maybe influenced for step emulation ( 20.000 steps / rev) which affect some velocity issues, them i had to stepdown this emulation and change velocities.
today i updated to Build 1537 and turn the drive to max emulation (20000steps/rev) and its running flowsly.
just to ensure i measure it with digital dial 0,001mm
one more time i would like to thank you for the impeccable work and to enable us to drive our machines with this greatest tool!
Last edited by 1125lbs (2017-06-21 17:55:22)
Offline
Thank you for sharing your experience
Offline
Pages: 1