You are not logged in.
Pages: 1
Hello,
I am new to the nanodlp community.
My printer shows the error "Failed to send image to GPU - Err Code 0" and does not print anymore.
It worked fine for 2 weeks.
Here is the application log:
Debug 1 2019-11-05 12:40:08.938586 Hardware Stepper motor enabled
Notice 1 2019-11-05 12:38:57.418202 Terminal Received Data From Controller: ok
Notice 1 2019-11-05 12:38:45.053462 Printing Printing xyzCalibration_cube Completed
Debug 1 2019-11-05 12:38:45.05319 Pulsing Moving to Stop Position
Debug 1 2019-11-05 12:38:43.275644 Shutter Shutter Close
Debug 1 2019-11-05 12:38:43.275508 Gcode Transferring Data G28
Warning 1 2019-11-05 12:38:43.275241 Printing Stop Command Received
Notice 1 2019-11-05 12:38:43.275126 Gcode Position change 3 to 3.1
Debug 1 2019-11-05 12:38:43.274585 Image Clear screen
Debug 1 2019-11-05 12:38:43.27396 Shutter Shutter Close
Debug 1 2019-11-05 12:38:43.273502 Image Clear screen
Error 1 2019-11-05 12:38:43.273404 Printing Failed to send image to GPU - Err Code 0
Error 1 2019-11-05 12:38:43.242133 Image Failure to display image, retrying.
Warning 1 2019-11-05 12:38:43.209914 Image Display layer public/plates/1/1.png
Notice 1 2019-11-05 12:38:41.218729 Terminal Received Data From Controller: ok
Notice 1 2019-11-05 12:38:41.218479 Terminal Received Data From Controller: X:0.00Y:0.00Z:0.10E:0.00 Count X: 0.00Y:0.00Z:0.10
Notice 1 2019-11-05 12:38:41.218316 Terminal Position set to 0.1
Debug 1 2019-11-05 12:38:41.209665 Shutter Shutter Open
Notice 1 2019-11-05 12:38:41.209365 Gcode Position set to 0.1
Debug 1 2019-11-05 12:38:41.209085 Gcode Transferring Data
M114
Info 1 2019-11-05 12:38:41.209001 Controller Sync Waiting for Z_move_comp response from Controller
Notice 1 2019-11-05 12:38:41.208707 Terminal Received Data From Controller: Z_move_comp
Info 1 2019-11-05 12:38:41.208375 Controller Sync Done message from Controller has been received
Info 1 2019-11-05 12:37:40.92487 Logging Suppressing duplicate logs
Notice 1 2019-11-05 12:37:40.924636 Terminal Received Data From Controller: ok
Notice 1 2019-11-05 12:37:40.924409 Terminal Received Data From Controller: ok
Notice 1 2019-11-05 12:37:40.924035 Terminal Received Data From Controller: ok
Debug 1 2019-11-05 12:37:39.72214 Gcode Transferring Data M650 D5.0000 S1.0000
M651
G4 P1000
G1 Z0.1
I am using an Raspberry Pi 3b with the NanoDLP build 2418.
The RP is connected to a projector through the HDMI port.
The Projector Calibration works just fine.
Can anyone help me?
Last edited by Querandus (2019-11-05 13:15:32)
Offline
It looks hardware issue, maybe power related. Change power source, HDMI cable and if you have spare rpi swap it.
Offline
Pages: 1