There are some not convenience and suggestions to fix

elshad66 · 2018-01-01 19:55:38

HI Shahin .HI ALL

I tested the latest Windows version ,,there are some inconveniences

eg, several items should be placed in the upper right corner ,,click Add Support With 3D Editor , A window opens and you need to click Plate view,
and table construction upside down,and you need to put in the lower left corner so that the model comes to the right-hand corner,
Button DO NOT ROTATE no work. only 90 work.and Each time you need to set the parameters. Decrease Mask Intensity .center origin and Mask File

if you need to edit the position of the part you need to remove the plates and do everything first.....because if you open 3D>>>EDIT FILE>>> PLATE VIEW
Models automatically come to the center,and it is no longer possible to edit

next
here was this problem with the mask,but I found the problem post#92 2017-11-02 16:47:20

https://www.nanodlp.com/forum/viewtopic.php?id=142&p=4

need to set the parameter Decrease Mask Intensity......why this parameter in the window Add Plate,,,it is necessary to transfer,, Mask Generation Wizard
to get out the final working mask,,and if you press Display Mask Preview opens final working mask,,with color for check

next
if I generate a new mask, it is not automatically saved in setup >>projector mask..(I waited a long time)
and if save mask in a third-party folder..and import .but no add....for adding need remove mask ...close/ run nanodlp and add mask

next
why need parameter Rotate Layers in the window Add Plate if have in Edit Profile .
and if you change Horizontal Resolution Vertical Resolution,Display automatically rotate
if the user needs to rotate the model ,, if there isn Plate view

I think that it is necessary to make both in all programs
1),,,adding Slicing start button in the Plates window
2)...if click Add Support With 3D Editor, opens Plate view,
3)..construction table in normal position,,if the model is set at the top right,and after cutting also at the top right
4)..adding mirror button in Plate view,
5)...grid make it permanent on construction table
6),,,adding keep the position of models on construction table,,if you open 3D>> EDIT FILE, so that the models are as originally set..
and could add model or something to remove or move or twist and save and after that click Slicing start button

Last edited by elshad66 (2018-01-01 20:41:59)

elshad66 · 2018-01-01 23:25:37

NEXT
405nm color corresponds to RGB 73,0,188 ..if inserted in Mask Generation ..Final Mask gives out a dark gray
To check it is necessary to cut a flat model or pillar and in settings in Add Plate in Decrease Mask Intensity 100
and open layers >>display layers and and measure with uv a sensor ,,sensor measurement does not correspond to,my settings mask

Shahin · 2018-01-02 06:50:09

eg, several items should be placed in the upper right corner ,,click Add Support With 3D Editor , A window opens and you need to click Plate view,
and table construction upside down,and you need to put in the lower left corner so that the model comes to the right-hand corner,
Button DO NOT ROTATE no work. only 90 work.and Each time you need to set the parameters. Decrease Mask Intensity .center origin and Mask File

I am not sure if I understand it correctly. Could you provide screenshot of what you want to change and how?

if you need to edit the position of the part you need to remove the plates and do everything first.....because if you open 3D>>>EDIT FILE>>> PLATE VIEW
Models automatically come to the center,and it is no longer possible to edit

It is by design, I am sure it is far from ideal.

here was this problem with the mask,but I found the problem post#92 2017-11-02 16:47:20
https://www.nanodlp.com/forum/viewtopic.php?id=142&p=4
need to set the parameter Decrease Mask Intensity......why this parameter in the window Add Plate,,,it is necessary to transfer,, Mask Generation Wizard
to get out the final working mask,,and if you press Display Mask Preview opens final working mask,,with color for check

Replied on the same post.

if I generate a new mask, it is not automatically saved in setup >>projector mask..(I waited a long time)
and if save mask in a third-party folder..and import .but no add....for adding need remove mask ...close/ run nanodlp and add mask

Hmm, you mean save mask button does not work for you?

why need parameter Rotate Layers in the window Add Plate if have in Edit Profile .
and if you change Horizontal Resolution Vertical Resolution,Display automatically rotate
if the user needs to rotate the model ,, if there isn Plate view

Without rotation STL arrangement on third party software also should be done on vertical space which is not ideal.

1),,,adding Slicing start button in the Plates window

We have regeneration button with the same functionality

2)...if click Add Support With 3D Editor, opens Plate view,

Do not get it.

3)..construction table in normal position,,if the model is set at the top right,and after cutting also at the top right

You mean some it should get centered?

4)..adding mirror button in Plate view,

On 3D editor page (add with support)?

5)...grid make it permanent on construction table

OK

6),,,adding keep the position of models on construction table,,if you open 3D>> EDIT FILE, so that the models are as originally set..
and could add model or something to remove or move or twist and save and after that click Slicing start button

I think it is same as above do not center feature, right?

elshad66 · 2018-01-02 23:40:50

HI Shahin
Thank you for your attention, please look at the screenshots here

http://moemesto.ru/elshad666/files

elshad66 · 2018-01-09 20:13:30

HI Shahin

from the fact that the raspberries very slow in performance
I was looking for different options ,and come to the fastest option
if everything is done on the win version and then send only png it to raspberry
so it turns out 3-4 times faster,,than to do everything in raspberries
for this I created a zip file only png,,and download zip from raspberries
and use raspberries as a sender and controller

there is a suggestion,if you can do so

1,,,so that nano creates a folder with name
2,,,created a zip file with only a png
3,,,name png wrote in this format -- ring0001.png

with this format can be inserted into cws and print from cw

so it was understandable look ring.jpg

http://moemesto.ru/elshad666/files

Thanks for your attention

Shahin · 2018-01-10 04:53:35

NanoDLP remote slicer feature is the exactly what you asking for.
Just run windows version on your system and work with RPi, it automatically detects windows version and offload slicing to your PC.

elshad66 · 2018-01-10 12:37:22

HI Shahin

I know, I checked but tests showed
there is no difference if the win is enabled or not

PC ip192.168.0.103 Constant in the router
PI ip192.168.0.101 Constant in the router
in setup in pi TCP 80 in TCP ip port of slicer enter 192.168.0.103 or leave empty (did restart ri )

I think that the remote slicer not active
maybe I'm not typing in correctly ? I only write 192.168.0.103,,how right?
or something else that needs to be configured in the router?
or something else that needs to be set up in the PC WIN 7 64?

Last edited by elshad66 (2018-01-10 20:09:01)

elshad66 · 2018-01-10 21:08:06

HI Shahin

Is it possible to reverse the direction of the cursor movement to the opposite?
eg
The cursor moves to the right and the plate turns to the right
and turn off the inertia motion

Thanks for your attention

Shahin · 2018-01-11 06:30:48

Default port for desktop version including windows is 8080.
I have to redesign whole support generator page as lots of people complaining about workflow and controls.

elshad66 · 2018-01-13 22:52:32

HI Shahin

I set up a mask for raspberries and for win
rectangle 0.1 thickness in 4 layers to output to the projector
edited many times changed mask intensity and click recreate
win version of the slicing in a couple of seconds
but raspberry about 1 min only 4 layers
every 5 seconds clicked update
windows is 8080
raspberries 80 IP if write or leave blank ... no difference slicing about 1 min
I do not know maybe they all conflict
wiring diagram all IP constants

http://moemesto.ru/elshad666/files

I still think that the created a zip file with only a png this will be the fastest option

Thanks for your attention

Last edited by elshad66 (2018-01-13 22:57:35)

MaxJewels · 2018-01-14 09:30:43

elshad66 wrote:

HI Shahin
I know, I checked but tests showed
there is no difference if the win is enabled or not
PC ip192.168.0.103 Constant in the router
PI ip192.168.0.101 Constant in the router
in setup in pi TCP 80 in TCP ip port of slicer enter 192.168.0.103 or leave empty (did restart ri )
I think that the remote slicer not active
maybe I'm not typing in correctly ? I only write 192.168.0.103,,how right?
or something else that needs to be configured in the router?
or something else that needs to be set up in the PC WIN 7 64?

Write 192.168.0.13:8080

elshad66 · 2018-01-14 17:06:24

MaxJewels wrote:

Write 192.168.0.13:8080

Yes it works, ,many thanks

elshad66 · 2018-01-14 23:32:34

Interestingly,
one raspberry, works perfectly after adding to pi 8080
but the second raspberry does not want to work quickly
remotely connected to other computers---same result on video
video.rar

http://moemesto.ru/elshad666/files

the first one is set to 16 gb 10 class Sandisk ultra --it works fine
and on the second 8 gb 10 class (maybe just a falsh wrote 10)
it possible that the SD is not the original,and therefore slows ?

the settings on both are identical 1771
and the same settings on the Win versions 1769

Last edited by elshad66 (2018-01-14 23:44:04)

nanoDLP

#1 2018-01-01 19:55:38

There are some not convenience and suggestions to fix

#2 2018-01-01 23:25:37

Re: There are some not convenience and suggestions to fix

#3 2018-01-02 06:50:09

Re: There are some not convenience and suggestions to fix

#4 2018-01-02 23:40:50

Re: There are some not convenience and suggestions to fix

#5 2018-01-09 20:13:30

Re: There are some not convenience and suggestions to fix

#6 2018-01-10 04:53:35

Re: There are some not convenience and suggestions to fix

#7 2018-01-10 12:37:22

Re: There are some not convenience and suggestions to fix

#8 2018-01-10 21:08:06

Re: There are some not convenience and suggestions to fix

#9 2018-01-11 06:30:48

Re: There are some not convenience and suggestions to fix

#10 2018-01-13 22:52:32

Re: There are some not convenience and suggestions to fix

#11 2018-01-14 09:30:43

Re: There are some not convenience and suggestions to fix

#12 2018-01-14 17:06:24

Re: There are some not convenience and suggestions to fix

#13 2018-01-14 23:32:34

Re: There are some not convenience and suggestions to fix

Board footer