nanoDLP

stig

Member

Registered: 2018-05-16

Posts: 19

Re: D7 and display issues

nope - sadly same result...

elshad66

Member

Registered: 2017-03-31

Posts: 118

Re: D7 and display issues

but  lcd   2560 1440 
  no 1920 1080

elshad66

Member

Registered: 2017-03-31

Posts: 118

Re: D7 and display issues

what is written in setup  2560 1440   or 1920  1080

elshad66

Member

Registered: 2017-03-31

Posts: 118

Re: D7 and display issues

where did you take  1920 1080

stig

Member

Registered: 2018-05-16

Posts: 19

Re: D7 and display issues

in the setup i have also written 1920x1080

elshad66

Member

Registered: 2017-03-31

Posts: 118

Re: D7 and display issues

If you have  lcd  2560 1440 then write to setup

stig

Member

Registered: 2018-05-16

Posts: 19

Re: D7 and display issues

i had 2560x1440 when i used the original LCD - changed it to 1920x1080 when i changed the /coot/config.txt to match my monitor

stig

Member

Registered: 2018-05-16

Posts: 19

Re: D7 and display issues

@Shahin - any ideas?  Or do i need to find a different software?

Shahin

Administrator

Registered: 2016-02-17

Posts: 3,541

Re: D7 and display issues

Remove projector on syscall

stig

Member

Registered: 2018-05-16

Posts: 19

Re: D7 and display issues

I must be blind - but i can not find this anywhere (in the GUI)

Shahin

Administrator

Registered: 2016-02-17

Posts: 3,541

Re: D7 and display issues

On the latest version of nanodlp it called "Execute to Turn Display On" on setup page.

miket402

Member

From: Las Vegas, NV

Registered: 2018-08-04

Posts: 8

Re: D7 and display issues

I am having the same issue with display screen 2K not showing image when printing.  I just finished building my printer two days ago.

***Screen displays an image when*****
        calibration it works fine(white, red, and white).
        in layer view I can get the image of any layer to print on the screen

Software is updated.

Raspberry Pi Full control
Relay (NO) controled by Raspberry pi to control led on/off
(TOS) NanoDLP Shield (5v voltage for 2k screen and raspberry pi, 12v for fan, limit switches and  control for the UV LED's)

Not using a stop button, LED or the I2C screen. Not really necessary when you have a wireless computer near by. My setup is the NanoDLP generic.

Thanks again for any help with this issue.

It will not allow me to post the link to the zip file? not sure how you can help now
maybe you have access to these sections. If so feel free to look at this
nanodlp.debug.-154132320.zip

Last edited by miket402 (2018-08-04 23:16:11)

miket402

Member

From: Las Vegas, NV

Registered: 2018-08-04

Posts: 8

Re: D7 and display issues

I was also wondering if this could be a heat issue within the Raspberry PI. My display shows 59c or 60c so it is no where near the 120c limit I was viewing in some other forums regarding a possible heat issue.

TomTuko

Member

Registered: 2018-09-20

Posts: 15

Re: D7 and display issues

I was having the same problems with the lcd/led printing. I did finally get it working at least for a dry run.

The final thing that fix it was loading the d7 firmware from the d7 easy install page.  So to summarize I installed the regular nanodlp on the sd card. Edited the config.txt file, loaded the d7 json file I found, edited the resin profile to remove the "WaitForDoneMessage"  and flashed the d7 firmware.

I made an image if the sd card before I expanded the file system. It has the printer working but you need to set the wifi locale before it will connect. I will try to get connected to my dropbox and upload the image tomorrow. Hopefully it will help someone else.

:-)

TomTuko

Member

Registered: 2018-09-20

Posts: 15

Re: D7 and display issues

Here is a link to and image I made after getting the regular nanodlp install to work with my d7.

https://www.dropbox.com/s/nco0kpu7y5q4z … 8.img?dl=0

This works with the d7 firmware on this page: https://3dprinterwiki.info/d7/easy-nano … ll-option/

You may still have to log into  a terminal session and run raspi-config to set the country code for the wifi before it will connect. Otherwise I think is good to go.