You are not logged in.

#1 2019-04-02 09:39:53

joebywan
Member
Registered: 2017-12-15
Posts: 14

Access to the button in current printer condition is forbidden error

This is for a nanodlp instance on a raspberry pi 3b+ with a Wanhao D7.

I get it's locking out the buttons due to some error, but I can't figure out what it's issue is that nanodlp is wanting to lockout the buttons.

"Access to the button in current printer condition is forbidden" is the error.

Level     Layer     Time     Module     Details
Warning    1    2019-04-02 09:30:07.230611    Access Control    Access to the button in current printer condition is forbidden
Notice    1    2019-04-02 09:25:52.923021    Terminal    Received Data From RAMPS: FlowMultiply:100
Notice    1    2019-04-02 09:25:52.919865    Terminal    Received Data From RAMPS: SelectExtruder:0
Notice    1    2019-04-02 09:25:52.919603    Terminal    Received Data From RAMPS: Free RAM:4958
Notice    1    2019-04-02 09:25:52.919353    Terminal    Received Data From RAMPS: Detected EEPROM version:17
UNKNOWN    2019-04-02 09:25:52.911226 {"Layer":"1","module":"Terminal","level":"Notice","msg":"Received Data From RAMPS: istart↵"}
Debug    1    2019-04-02 09:25:49.134902    WiFi    Connected to
Debug    1    2019-04-02 09:25:43.911975    Gcode    Transferring Data M107
M106 P1 S255
Debug    1    2019-04-02 09:21:44.273852    WiFi    Status Monitoring
Warning    1    2019-04-02 09:21:44.273707    WIFI    WIFI interface wlan0 detected
Debug    1    2019-04-02 09:21:44.131368    Gcode    Transferring Data M107
Notice    1    2019-04-02 09:21:44.131118    Terminal    Terminal Reader Activated
Debug    1    2019-04-02 09:21:44.131033    Shutter    Shutter Close
Error    1    2019-04-02 09:21:44.052689    Gcode    Could not access LCD write /dev/i2c-1: input/output error
Notice    1    2019-04-02 09:21:44.041116    Hardware    Initializing build # 2065 - generic

The log prior.

The setup was working last time I turned it on, it did do an update tonight though.

If there's anymore information I can give, let me know.

Link to the debug info: https://www.dropbox.com/s/c01y8cf5o34l6 … 4.zip?dl=0

Thanks

Offline

#2 2019-04-02 15:05:15

Shahin
Administrator
Registered: 2016-02-17
Posts: 2,541

Re: Access to the button in current printer condition is forbidden error

Which button does not work?

Offline

#3 2019-04-02 16:33:47

joebywan
Member
Registered: 2017-12-15
Posts: 14

Re: Access to the button in current printer condition is forbidden error

Crap sorry.  The stir, home, move up or down buttons.  Basically anything to do with z axis control

Offline

#4 2019-04-02 21:44:57

Shahin
Administrator
Registered: 2016-02-17
Posts: 2,541

Re: Access to the button in current printer condition is forbidden error

Not sure why it happening, please share a debug file.

Offline

#5 2019-04-02 22:01:53

joebywan
Member
Registered: 2017-12-15
Posts: 14

Re: Access to the button in current printer condition is forbidden error

There's already a debug file linked in the first post.

Offline

#6 2019-04-03 10:18:04

joebywan
Member
Registered: 2017-12-15
Posts: 14

Re: Access to the button in current printer condition is forbidden error

After playing with it more, I'm able to manually home it through the ramps terminal in nanodlp sending G28.  So I'm assuming it's something in nanodlp locking me out from using the buttons because it doesn't like something with the printer.

Offline

#7 2019-04-04 16:38:58

Shahin
Administrator
Registered: 2016-02-17
Posts: 2,541

Re: Access to the button in current printer condition is forbidden error

Save buttons again, issue will get solved.
Also I have pushed update which will fix this issue.

Offline

Board footer

Powered by FluxBB