Info 1 2016-09-15 21:05:57.134215 Terminal Received Data From RAMPS: Z_move_comp
Info 1 2016-09-15 21:05:57.129328 Terminal Received Data From RAMPS: ok
Info 1 2016-09-15 21:05:50.235576 Terminal Received Data From RAMPS: Z_move_comp
Info 1 2016-09-15 21:05:50.231735 Terminal Received Data From RAMPS: ok
Info 1 2016-09-15 20:57:02.909536 Gcode Waiting for done message from controller
Info 1 2016-09-15 20:57:02.907523 Terminal Received Data From RAMPS: ok
Info 1 2016-09-15 20:57:02.906623 Terminal Received Data From RAMPS: ok
Debug 1 2016-09-15 20:57:02.903817 Gcode Transfering Data G01 Z0.1 F100 ;
Info 1 2016-09-15 20:57:02.903303 Terminal Received Data From RAMPS: ok
Debug 1 2016-09-15 20:57:02.902106 Pulsing Moving to Layer
Info 1 2016-09-15 20:57:02.901741 Projector Projector on
Debug 1 2016-09-15 20:57:02.901513 Gcode Transfering Data M280 P2 S10
Debug 1 2016-09-15 20:57:02.900559 Shutter Shutter Close
Debug 1 2016-09-15 20:57:02.900439 Image Clear screen
Info 1 2016-09-15 20:57:02.900335 Projector Projector on
Info 1 2016-09-15 20:57:02.900209 Gcode Position set to 0
Debug 1 2016-09-15 20:57:02.899539 Gcode Transfering Data G90
G92 X0 Y0 Z0
I will add force stop.
]]>When you put [[WaitForDoneMessage]] message into gcode box, nanoDLP waits until receive Z_move_comp message from ramp board.
Quite interestingly your ramp only sends 'ok' messages back, are you sure you are using patched marlin firmware?
If you are using patched version, is there any similarity for profiles which has this issue?
Stop only works when ramp returns back the control.
Maybe we need force stop somewhere buried inside setup page.
]]>Error - 2016/03/11 14:52:12.486369 Access Control Printing in Progress -
Error - 2016/03/11 14:51:58.767828 Access Control Printing in Progress -
Warning - 2016/03/11 14:45:29.074618 Hardware Settings saved but critical settings could not switched in the middle of print. If you need all settings to be take effect stop the printer and submit again.
UNKNOWN 2016/03/11 14:42:31.824997 {"Layer":"-","module":"Terminal","level":"Info","action":"Data Received","msg":"ok
UNKNOWN 2016/03/11 14:42:31.824473 {"Layer":"-","module":"Terminal","level":"Info","action":"Data Received","msg":"ok
Info - 2016/03/11 14:42:18.743721 GCODE Waiting Waiting for done message from controller
Info - 2016/03/11 14:42:18.743364 GCODE Transfering Data ;M280 P2 S90; used with shutter wired to the ramps↵;M650 D4.0000 S1.0000↵;M651↵;G1 Z0.1↵
Info 1 2016/03/11 14:42:18.739899 Z-Axis Moving to Layer 1 -
Info - 2016/03/11 14:42:18.739194 Projector Turn On The Projector -
UNKNOWN 2016/03/11 14:42:18.734209 {"Layer":"-","module":"Terminal","level":"Info","action":"Data Received","msg":"ok
Info - 2016/03/11 14:42:18.726073 Shutter Shutter Close -
Info - 2016/03/11 14:42:18.725844 Image Clear Screen -
Info - 2016/03/11 14:42:18.725386 Projector Turn On The Projector -
Info - 2016/03/11 14:42:18.725068 GCODE Transfering Data ;M280 P2 S0; ramps wired shutter↵M650 D5 S5 ↵G28↵G91↵
UNKNOWN 2016/03/11 14:41:55.888400 {"Layer":"-","module":"Terminal","level":"Info","action":"Data Received","msg":"ok